The Catnic Wall Starter Kit 2.4m is a stainless steel wall starter system for tying new masonry walls into existing brickwork or blockwork. It is commonly used as a brick wall starter kit for extensions, internal walls, external walls and other building work where a new wall needs to be securely connected to an existing structure.

The Catnic Stronghold wall starter kit includes adjustable wall starter ties, plugs, coach screws, washers and fixing instructions, giving you the main components needed to install a new masonry wall starter system straight from the box.

Key Features

Catnic Stronghold wall starter kit
2.4m wall starter system
Used for tying new walls into existing masonry
Suitable for brickwork and blockwork applications
Adjustable wall starter ties for flexible coursing
Universal application up to 250mm wall thickness
Suitable for internal and external use
Supplied with wall starter ties, plugs, coach screws, washers and fixing instructions
British made

Kit Contents

Component	Quantity
Stainless steel wall connector strips	2 x 1.2m lengths
Wall starter kit ties	10
Wall starter kit plugs	5
Coach screws	5
Washers	5
Fixing instructions	Included

Specification

Product	Catnic Stronghold Wall Starter Kit
Product type	Wall starter kit / wall starter system
Overall height	2.4m
Connector strips	2 x 1.2m stainless steel strips
Material	Stainless steel 1.4016 to BS EN 10088-2
Maximum wall thickness	Up to 250mm
Application	Tying new masonry walls into existing brickwork or blockwork

Brick Wall Starter Kit for New Walls

A wall starter kit is used when a new wall needs to be connected to an existing wall without cutting out masonry. The stainless steel starter strips are fixed vertically to the existing structure, then the wall starter ties are slotted into the strip and built into the mortar joints of the new wall.

The adjustable tie system allows the ties to move up or down within the starter strip, helping them align with the brick or block coursing on site. This makes the Catnic wall starter kit suitable for a range of masonry wall starter applications.

Internal Wall Installation

For internal wall construction, line up the wall starter kit with the centre line of the new wall and ensure it is plumb. Fixing positions for the coach screws should avoid mortar joints wherever possible.

Use a 10mm masonry drill bit, insert the plugs, then fix the lower starter strip first without overtightening the screws. Offer up the upper starter strip, mark the fixing points, and repeat the process for the upper section.

External Wall Installation

For external cavity wall construction, a wall starter kit should be used for both the internal and external leaves. The bottom end of the wall starter kit must be positioned above the damp-proof course.

Outer leaf vertical joints between the new and existing walls should be weather-sealed with a proprietary sealing strip or suitable polymer-based sealant. In exposed or maritime locations, additional damp-proofing measures may be required, so check whether a vertical DPM is needed for the project.

Wall Starter Ties

The supplied wall starter ties slot into the starter strip and can be adjusted up or down to suit the coursing. The twist-and-lock system holds the ties securely in place, helping create a positive connection between the existing masonry and the new wall.

The wall starter ties should be laid onto a full bed of mortar and fully covered within the mortar joint.

Important Selection Note

Before ordering, check the wall thickness, wall type, internal or external application, damp-proofing requirements and any engineer, architect, building control or warranty-provider requirements. For external cavity wall construction, remember that two wall starter kits may be required: one for each leaf.

FAQs

What is a wall starter kit used for?

A wall starter kit is used to tie a new masonry wall into an existing brickwork or blockwork wall. It provides a starter strip and adjustable ties so the new wall can be connected securely without cutting out the existing masonry.

Can this be used as a brick wall starter kit?

Yes. The Catnic wall starter kit is suitable for brickwork and blockwork applications where a new masonry wall needs to be tied into an existing structure.

Do the wall starter ties slide up and down?

Yes. The wall starter ties can be adjusted within the starter strip to suit the coursing of the new wall.

Does the kit include the twist-and-lock wall ties?

Yes. The kit includes wall starter ties designed to slot into the starter strip and lock into position.

How many wall starter kits do I need for an external cavity wall?

For an external cavity wall, two kits are normally required: one for the internal leaf and one for the external leaf.

For delivery, collection or project support, contact the Wade team.

Download the Catnic Stronghold Wall Starter Kit data sheet and installation instructions.